-
一适用：
莱卡布,牛仔布(涂层布，压光布除外)、尼龙布、TPU、PU皮革，及一些高弹性面料等.
二．性能指标：
外观及组成：白色状粘稠体，聚氨酯聚合物
布氏粘度：140000~160000CPS
PH值：7.0-8.0
离子类型：阴离子
固体含量：65%±1
三．特性：
立体感强，触边性好，高附着力，高亮光，高弹性，手感超柔软，抗回粘性能优。表面光滑，牢度超强。耐高温水洗、雪花洗、漂洗、酵素洗、酸洗、耐高温蒸煮。（避免45℃以上高温或—35℃以下低温）优越的低温耐折。耐黄变.常温下保存12个月，属于高端环保型胶浆。本产品已通过国际一线品牌（耐克，卡帕，阿迪达斯）耐折，水洗反复测试。得到了权威的认可。
PU0360立体水性墨白（机印超柔软，似硅胶，双组份）：立体感强，触边性好，高附着力，高亮光，拉伸力好，手感软，柔软似硅胶，干爽，耐高温水洗，抗回粘性能优。优越的低温耐折型，适合于机印
PU0360立体水性墨透（机印超柔软，似硅胶，双组份）：立体感强，触边性好，高附着力，高亮光，拉伸力好，手感软，柔软似硅胶，干爽，耐高温水洗，抗回粘性能优，干擦4-5级，湿擦4级。优越的低温耐折型，适合于机印
四．操作应用：
1．本产品一般使用80目120目网布，根据图案的不同丝网一定要绷紧，这一点相当关键：
2．为了保证印制效果，一般不要制作太厚网版，根据厚度不同需要印5—8次，在使用厚网版印刷时印完第一次需待底层干透后再进行第二次印刷，一般印刷3—5次就能达到2-3毫米以上的高度。
3．本产品不易塞网，过稠时可加入适当水浆搅拌均匀进行稀释。
4．在自然风干48小时后，再过温150度8-15秒，过温时尽量将面料过反面。
5．使用时加入1%-2%交联剂。（加好助剂的浆料要在3~6小时内用完）
五、注意事项：
1、自然干燥时间与气温和空气湿度有关。
2、调色可根据客户需要颜色的深浅来调入色种的分量，颜色调入太多容易引起掉色现象，色种最好控制在5%之内.
3、如印容易掉色的深色布，需要测试颜色是否会升华到胶浆表面上，以减少不必要的损失。
4、使用本透明产品印花，要稍加白胶浆掺和进行调色印花有利于在纺织品面料上印花着色度饱和，更好发挥透明浆的应用效果
5、由于印花面料的多样化，和一些外在的不确定因素做大货之前先小样实验确定以后方可批量生产。未确定情况使用或操作不当引起的质量问题本公司概不负责.
Other detailed information
Brand
Conghui
Model
0360
Viscosity
/
PH Value
7.0-8.0
Odor
/
Strength
100T
Fineness
/
Appearance
/
Usage
/
Color strength
100%
Fluidity
/
Shelf life
12months
Single net weight
20KG
Resin type
/
一．Substrates:
Lycra, denim(except coated fabric, press polishing fabric),nylon,TPU, PU leather and some high stretch fabric.
二．Performance indicators:
Appearance and composition: milky white viscous body, polyurethane polymer
Brinell viscosity:140000-160000CPS
PH Value:7.0-8.0
Ionic: anion
Solid content:65±1%
三．Features :
Super tomographic view, good side,high adhesion,glossiness and elasticity.super soft hand feel.Excellent anti after-tack,stain finish.Resistant to washing by high-temperature, snow wash,bleach,enzyme wash and acid wash. High temperature resistance steaming, yellowing resistance .The shelf life is 12months under normal temperature,belongs to high-end environmental paste.
PU0360 Stereo waterbased ink white（machine printing,super soft,just like silicone,two-component.）：High three-dimensional sense,good edge,high adhesion,high glossiness,high tensile strength,soft hand feel,just like silicone,dry,resistance to high temperature washing,excellent performance of non-after tack.Excellent low temperature folding.By the way,it is suitable for machine printing.
PU0360 stereo waterbased ink clear（machine printing,super soft,just like silicone,two-component）：High three-dimensional sense,good edge,high adhesion,high glossiness,good tensile strength,soft hand feel,just like silicone,dry,resistance to high temperature washing,excellent performance of non-after tack,the dry rub is 4-5 degree,the wet rub is 4 degree.Excellent low temperature folding.By the way,it is suitable for machine printing.
四．Operation application
1.This product usually use 80-120mesh screen, according to different patterns,the silk screen should be tightened, this one is very crucial.
2.In order to guarantee the printing effect,do not use too thick screen as usual,according to different thickness,print 5 or 8 times,when using thick screen to print,print in second time after the base dries completely in first time,as usual ,it can reach 2-3mm when printed 3-5times.
3.This product is not easy to mesh plug,when it is too thick, you could add appropriate water to stir evenly and mildly.
4.After air dry for 48 hours,and overheat at 150℃for 8-15seconds,when in the process of overheating should put the fabric in opposite side.
5.When using it,you could add 1%-2% catalyst or cross-linker.
五．Notes
1.The time of air dry is related to temperature and air humidity.
2.Adjusting color according to shade of color that customers need to add amount of pigment.If add too much it will lead to phenomenon of rubbing off, the amount of pigment should be controlled within 5%.
3.If prints on dark fabric that is easy to rub off, should be test color whether it sublimates on the surface of fabric,in order to reduce unnecessary financial losses.
4.Using clear product to print,should add white paste to adjust color printing,it makes printing looks full and reach the better application effect of clear paste.
5.Due to variety of fabric and some uncertain factors , you should make a test before in a batch production.Our company is not responsible for quality problem which caused by wrong operation or using under uncertain condition.