<-----  向左滑动显示详细信息

适用范围]:

适用于棉、涤棉、梭织棉面料等的仿拔染印花。

(不受染料或非染料的面料限制。 甚至对含涤纶成分较高的混合棉料进行仿拔白印花。)

[性 质]:

外 观: 乳白色糊状物

主成分: 丙烯酸聚氨酯共聚物、精细钛白

离子性: 阴离子

[保 质 期]:

室温5-35℃,避免暴晒 或 冷冻, 贮存1年。

[特 征]:

稳定性良好，精细光滑，纹理清晰，接近拔印效果，透气性好，能在深色布上进行彩色印花的高遮盖水浆,色泽饱满、遮盖力较强、牢度好、手感较软、无异味、无腐蚀性,环保指数达国际环保织物要求。

[一般配比]:

仿拔染水浆(拔白浆) 100-97%

固色剂/交联剂 0-3% (酌情少放)

100克

印花工艺：(Mesh网布80-100目) 印花1次1-2刀 → 烘干、干燥 → 可用隧道烘箱烘焙 或 压烫。

[注意事项]:

先将布铺平,跑道烘车将布片的水份蒸发后,再印花效果更佳。

1) 先把浆料上下搅拌均匀。

2) 根据面料的(棉、涤)成分,选择合适的固色剂或交联剂(注意固色剂的时效性) ,避免使用阳离子助剂。

3) 以日本印花惯例:调浆后 印刷前,先把浆料过滤一次,使浆体更细腻,色泽更均匀,手感更流畅,效果更佳。(推荐)

4）干透后再进行烘箱热处理,可以有效增加牢度。印花24小时后,方可测试牢度。 若：要手感好,建议少放固色剂/交联剂,烘焙温度尽可能控制在80℃以内(高温会导致手感偏硬)。刚烘干的印花面,手感偏硬,随着时间的推移(隔天)会变柔软。

-------------------------------------------------------------------

上述资料,仅供参考,不作法律依据。按“国际化工惯例”：每次使用前,客户必须试验确认后,方可批量投入使用,否则后果与我方无关

Other detailed information

Brand	Conghui	Model	G50-2
Viscosity	/	PH Value	/
Odor	/	Strength	100T
Fineness	/	Appearance	/
Usage	/	Color strength	100%
Fluidity	/	Shelf life	12months
Single net weight	25KG	Resin type	/

Scope :cotton, mercerized cotton, woven cotton

[Characters]:

Appearance :milky white viscous body

Main component: acrylic polyurethane copolymer, fine titanium dioxide

Ionic: anion

[shelf life] :

At room temperature5-35℃,avoid exposure or freeze,the shelf life is one year.

[Features ]:

Good stability,fine and smooth,clear textures,close to discharge effect,good permeability,which is a high covering slurry that can print on the dark fabric.

Saturated color,super coverage,good fastness,soft hand feel,odorless, the environmental indicator reaches international textile's requirements

[Ratio]:

Discharge like water paste(discharge like white) 100-97%

Fixing agent/cross linker 0-3%(or less)

100g

Printing technology:(mesh screen 80-100)print one time scrape once-twice →drying→hot pressure

[Notes] :

Pull down fabric first and evaporate water,then printing effect is better.

1)stir paste evenly and mildly in first time

2)According the component of fabric,choosing proper fixing agent or cross linker(pay attention to timely),avoid to use cationic auxiliaries.

3)According to Japanese printing regulars: after adjusting paste,before printing,filter the paste for one time,make the paste more stained,the gloss is more evenly and mildly,good hand feel and better effect.

4)After drying,making heat pressure by dryer to increase fastness. If: need good hand feel,advice to use litter fixing agent/cross linker,temperature of baking should be controlled within 80℃（high temperature will lead to hard hand feel.）the surface of printing,hand feel is prefer to be hard,with time goes by, it becomes softer.